Grain Handling & Milling
Malt Mill
· 4400 lbs/hr (2000 Kg/hr)
· Adjustable legs
· 6 1/2″ (165mm) diameter solid steel rolls
· A single lever setting for rolls
· Rolls grooved and hardened to 60 Rockwell C Roller spacing and pressure are easily adjustable
· Large Capacity hopper c/w tramp metal magnet
· Adjustable slide gate for controlling input
· 1.75″ shafts to withstand pressure from cracking malt
· 5 HP EXPLOSION PROOF MOTOR INCLUDED
· 51″ (130 cm) long x 28″ (71 cm) wide x 51″ (130 cm) high
· Weighs 620 lbs (281 kg)
· Price includes exit adapter
· Optional 5″ inclined discharge auger available
Flex auger – unloader, boot and bearing
· Required to connect flex auger inlet to mill or grist case
· 16″ rubber boot
· Straight boot or 30 degree boot available Single-out unloader
· Flex auger anchor bearing
· Flex auger bearing assembly
350 Flex Auger to Grist Case
· Drive motor and control unit is included
· Body is rugged PVC Tubing for long service life
· Can be customized to meet most site conditions. Grist capacity up to 3000 lbs/hr (1360 kg/hr)
· Malt capacity up to 4500 lbs/hr (2041 kg/hr)
Poly Grist Case
· Polyethylene hopper for malt or grist Semi transparent for level indication
· Complete with frame, hopper and roof
· Includes floor mount kit Gross capacity of 72 cu ft
· 1440 lbs of milled grist at 20 lbs/cu ft
· 2160 lbs of unmilled malt at 30 lbs/cu ft Standard 16″ opening
· Suitable for 5 – 20 bbl systems
· 60″ diameter
· 109″ overall height
350 Flex Auger to Grist Hydrator
· Drive motor and control unit is included
· Body is rugged PVC Tubing for long service life
· Can be customized to meet most site conditions.
· Grist capacity up to 3000 lbs/hr (1360 kg/hr) Malt capacity up to 4500 lbs/hr (2041 kg/hr)
Grist Hydrator 4″ (102 mm) (C/W Thermometer)
· Ureathane flex hose above valve
· 4″ butterfly valve directly above hydrator S/S construction
· T/C connection to Mash/Lauter Tun
· T/C water inlet connection
· Sleeve for connection to grist auger
· Combines grist and water entering Mash/Lauter Tun
· 3″ (76 mm) dual scale dial thermometer installed in 1/2″ (13mm) CPLG for reading outlet temperature
· 5,000 lb/hr
· Approximate weight = 7 LB’S (3.2 kg)
Water Systems
40 BBL Hot Liquor Tank
· Design pressure: Atmospheric 4 Legs c/w adjustable Footpads.
· Shell material t304 2b s/s Cladding material t304 #4 s/s
· Interior weld finish = stain removed and brightened on a regular margin and Acid Cleaned.
· Exterior weld finish = stain removed and brightened on a regular margin.
· Cladding penetrations are stain removed and brightened on a regular margin.
· Shallow cone top, Shallow cone bottom Insulation & cladding on sides and bottom
· Top fittings: Atmospheric manway, CIP c/w 1″ (25mm) side arm & sprayball, 1″ (25mm) water inlet Side fittings: Liquid level sight tube..
· Bottom fittings: 1.5″ (38mm) Triclamp Drain, thermowell, 1.5″ (38mm) overflow.
· Approximately 30% Head Space.
· Steam jackets designed to heat vessel full volume of water from 70F TO 180F in 12 hours
Hot Liquor Pump
· Stainless steel pump
· Washdown duty motor
· Includes floor mount
40 BBL Cold Liquor Tank
· (Stock Code ZCL040.CN) Design pressure: Atmospheric
· 4 Legs c/w adjustable Footpads. Shell material t304 2b s/s Cladding material t304 #4 s/s
· Interior weld finish = stain removed and brightened on a regular margin and acid cleaned.
· Exterior weld finish = stain removed and brightened on a regular margin.
· Cladding penetrations are stain removed and brightened on a regular margin.
· Shallow cone top, Shallow cone bottom
· Insulation & cladding on sides and bottom.
· Top fittings: Atmospheric manway, CIP c/w 1.5″ (38 mm) side arm & sprayball, 1.5″ (38 mm) water inlet
· Side fittings: Liquid level sight tube.
· Glycol Jacket to cool 130% of the volume from 65F to 34F in 12 hours using glycol at 28F.
· Bottom fittings: 1.5″ (38 mm) triclamp Drain, thermowell, 1.5″ (38mm) overflow.
· Approximately 30% Head Space.
Cold Liquor Pump
· Stainless steel pump
· Washdown duty motor Includes floor mount
Browhouse Equipmen
20 BBL Lauter Tun
· Design pressure: Atmospheric,
· 4 of 4″ (100mm) Legs c/w adjustable footpads. 3/4″(19mm) thread
· Shell material t304 2b s/s, Cladding material t304 #4 s/s
· Interior weld finish = stain removed and brightened on a regular margin. Exterior weld finish = stain removed and brightened on a regular margin.
· Cladding penetrations are stain removed and brightened on a regular margin.
· Formed top head, flat bottom, Insulation on sides.
· Top fittings: Atmospheric manway, 1″ (25mm) CIP, sparge piping c/w nozzles
· VFD Controlled top mounted motor for stirring rakes.
· Side fittings: Thermowell
· Bottom fittings: Wort outlets, Wedge-wire false bottom, 1.5″(38mm) wort collection header, spent grain removal port.
· Design parameters: 12 deg Plato original gravity, 95% brewhouse
· Efficiency, 77% available extract, 180 kg/sq meter plate loading. 70″ ID, 5′ SIDE
· New flat bottom design reduces under-plate volume, reduces under-dough,
· And reduces the turbidity During Vorlauf and Wort Transfers. This results in a higher brewhouse efficiency and higher yields.
· Note: Spent grain port requires 12″ knife gate valve sold separately
Lauter Tun Differential Pressure Sensor
· 2x differential pressure sensors with transmitter Readout on HMI/Brehouse control panel
· Measures diferential presssure above and below the grain bed
Magnetic Particle Sanitary Flow Meter
· Magnetic flow meter
· Sanitary Magnetic flow meter
· Size: 1.5 inch (38mm), Tri-Clamp connection Integral Signal Converter
· Supply: 120 Vac
· Indication of flow and total flow
12″ (300 mm) Knife Valve (Wheel)
· 12″ (300 mm) stainless steel knife valve
· Lauter tun spent grain bottom manway knife valve Stainless steel wetted parts
· 0-ring elastomer seal
· Large handwheel for easy operation
20 BBL Steam Kettle / Whirlpool
· Design pressure: Atmospheric
· 4 Legs c/w adjustable Footpads. Shell material t304 2b s/s
· Cladding material t304 #4 s/s
· Flat bottom cladding T304 2B s/s
· Interior weld finish = stain removed,, polished to #4 on a regular margin
· Exterior weld finish = stain removed and brightened on a regular margin.
· Cladding penetrations are stain removed and brightened on a regular margin.
· Formed conical head, shallow cone bottom.
· 1.5″(38mm) Mineral Wool Insulation on sides and bottom.
· Steam jackets for low pressure steam.
· Jackets will boil the full volume at 6% evaporation per hour.
· Top fittings: 8″(204mm) vapor vent, 1″(25mm) water inlet, condensate drain
· 18″(458m) manway, 1″(25mm) CIP
· Side fittings: whirlpool inlet, thermowell, steam jackets
· Bottom fittings: drain, wort draw-off, steam jacket
· Approximate Dimensions: 66″(1679mm) ID, 6′(1.8M) SIDE Stack sold separately
· The price includes the tank placed in a mild steel cradle for shipping.
Kettle Boil Over Sensor
· Detects over boil in the Kettle and sends signal to cut steam.
Hop Dosing Port Upgrade – Steam Kettle
· System to allow for safe additions of hops to kettle while boiling
· 4″ tri clamp hop dosing port on head of vessel
· 4″ butterfly valve, 4″ ferrule, 4″ clamp, 4″ gasket, 4″ cap
· S/S open Hopper
Work Platform
· Stainless steel construction throughout
· Handrails on stairs and platform
· Convenient working height for brewhouse vessels
· Control panel mounted on handrail
· Liquor Blending Station can be mounted on the rear hand rail.
Control Panel Mounting Bracket
· Stainless steel construction throughout, Glass Beaded Finish.
· 1.5″ tube frame holds control panel and up to 3 VFD’s
· Frame mounts to the work platform railings using tube hangers.
40 BBL Unitank
· Vessel working pressure: 15 PSI (1 BAR) Jacket working pressure: 29 PSI (2 BAR) Working pressures are subject to local codes
· 4 Legs c/w adjustable Footpads. Shell material t304 2b s/s, Cladding material t304 #4 s/s
· Interior weld finish = stain removed, polished on a regular margin and acid cleaned.
· Exterior weld finish = stain removed and brightened on a regular margin.
· Cladding penetrations are stain removed and brightened on a regular margin.
· Formed top head, 60 degree cone bottom Insulation sides and bottom.
· Top fittings: CIP c/w 1.5″ side arm, spray ball, 2.5″ PVRV, manway (top or side)
· Side fittings: glycol couplings, thermo-well, sample port, manway (top or side)
· Jackets are sized to cool the working volume from 65F to 34F in 24 hours using a glycol inlet temperature = 30F.
· Bottom fittings: Drain & valve, racking ferrule & valve, glycol couplings.
· Relief pressure 15 psi, Relief vacuum 1psi.
· Minimum additional head space 25%
· The price includes the tank placed in a mild steel cradle for shipping.
· Racking arm and valve.
· CIP arm end piece including gauge, ball valve, quick disconnects. PVRV valve.
40 BBL Bright Beer Tank
· Vessel working pressure: 15 PSI (1 BAR) Jacket working pressure: 29 PSI (2 BAR) Working pressures are subject to local codes 4 Legs c/w adjustable Footpads.
· Shell material t304 2b s/s Cladding material t304 #4 s/s
· Interior weld finish = stain removed, polished on a regular margin and acid cleaned.
· Exterior weld finish = stain removed and brightened on a regular margin. Cladding penetrations are stain removed and brightened on a regular margin.
· Formed heads top and bottom.
· Insulation on sides and bottom.
· Top fittings: CIP c/w 1.5″ side arm and sprayball ( top sight tube,
· Ball valve for top pressure, pressure gauge), 2.5″ PVRV manway (Top or side).
· Side fittings: Glycol jackets designed to cool the tank volume from 65F to 55F in 10 hours using glycol at 28F, thermowell, sample port, carbonating ferrule and stone
· Bottom fittings: 1.5″ drain c/w B/F valve Relief pressure 15 psi, Relief vacuum 1psi.
· The price includes the tank placed in a mild steel cradle for shipping. PVRV Valve.